400 CFM MOISTURE SEPARATING SYSTEM TX-MSS-400
$12,250.00 Original price was: $12,250.00.$11,147.50Current price is: $11,147.50.
The TX-MSS-400 has a 2 inch inlet with a screened 4 prong crowfoot fitting and a safety lock cable. The primary outlet is 2 inch with an OSHA compliant auto exhaust ball valve and a 4 prong crowfoot fitting. The system has 4 additional air outlets equipped with OSHA compliant 3/4 inch auto exhaust ball valves and 2 prong crowfoot fittings. All outlets have safety lock cables to limit the travel of erratic hoses in case of hose breakage or accidental disconnection.
The system’s manifold tank has three additional outlet ports that can be configured with ball valves and crowfoot fittings. A fourth outlet is utilized by the system and provides compressed air to the air mover which is used to pull ambient air through the aftercooler. The Aftercooler is the primary moisture separating component. The ambient air is being pulled through the cooling fins of the aftercooler to remove heat from the compressed air that is flowing through the interior of the aftercooler. The rapid cooling of hot compressed air causes moisture vapor to condense into liquid. The liquid then falls to the bottom of the deliquescent desiccant tank where it is expelled via the 1/2 inch ball valve on the bottom. This valve is kept slightly open during operation to continually remove water from the system.
These systems are ideal for removing moisture prior to sand blasting or painting. However, they can be used to remove moisture that can damage air tools like impact wrenches and grinders. Tools can run off the additional outlet ports or additional manifolds can be used in conjunction with the moisture separator systems. For example a TX-2AMF, TX-4AMF or TX-5AMF can be connected via a two inch outlet of the moisture separating system. The manifolds provide a centralized distribution point, and because the compressed air has already been cooled the moisture has been removed, all downstream compressed air is dry. Portable In Line lubricators and Filter/Lubricator should be used with any air tool to provide lubrication during use. Texas Pneumatic Hose Whip assemblies can be configured for most applications.
Related products
- Abrasive Blast Equipment and Parts
- Air Ducting Tx-Sac-N-Go
- Air Manifold, Stationary, Horizontal w/large Inlet/Outlet
- Air Manifolds Tank Style
- Air Misters
- Air Movers
- Air Receiver Tanks A.S.M.E. Approved
- Air Scribe And Repair Kit
- Double Diaphragm Pumps
- Foundry Tools
- Industrial Magnets
- Jet Fans and Swing Gates
- Lubricators and Hose Whips
- Man Coolers
- Marine Blowers (Water Driven)
- Moisture Seperating Systems
- Paint Booth Supplies
- PAVING BREAKERS
- Pneumatic Chipping Hammer
- Pneumatic Light
- Pneumatic Paving Breakers
- Pneumatic Pipe Line Blowers 2-8 Inches
- Portable Dust Collection Systems
- Portable F-R-L Systems (Filters-Regulators-Lubricators)
- Rivet Busters
- Rock Drills
- Scaffpads
- Scaling/Chipping Hammers
- Shipboard Rat Guards
- Tornado Blowers (Vaneaxial)
- Truck Accessories
- Uncategorized
- Wizbangers U.S. Navy Style Double Diaphragm
Get In Touch With An Expert!
Ave questions about your order? Reach out to our contact line and get connected with an Abundant Supply Representative to assist you with all of your needs!
Best Products
-
TX-133-6RB-OT - 6 INCH RIVET BUSTER WITH OUTSIDE TRIGGER
$1,725.00Original price was: $1,725.00.$1,353.00Current price is: $1,353.00. -
TX-SAC-N-GO-8-C - 8 INCH X 30 FT ELECTRICALLY CONDUCTIVE DUCTING WITH ATTACHED STORAGE BAG
$675.00Original price was: $675.00.$614.25Current price is: $614.25. -
Wizbanger 1 1/2" Pneumatic (Bilge Pump)
$1,129.54Original price was: $1,129.54.$854.40Current price is: $854.40.
Reviews
There are no reviews yet.